RV Luxury Options

Were I to try to list ALL of the luxury options available to RVers, the list would be endless.   No doubt there are new inventions being created that would make the list out of date before I could click "Publish".  By the time you read the list, new additions might even be obsolete!  With that in mind I will list some of the more popular and desirable features that are standard usually only on high end luxury units but often envied by the rest of us.  Keep in mind that "luxuries" are, by definition, nice to have but usually not essential.   However, it is surprising how quickly some luxuries become necessities to some people.   Luxury features are usually not standard equipment on production vehicles except for very high end units but are often ordered or added by owners by the time they hit the used market.

The sky is the limit!   There is virtually no end to ways you might enhance your RV if you have the initiative, imagination, and money.  I've even seen RVs with a hot tub!  While that is probably not a practical or even desirable option for most people, there are many luxury options that are useful, realistic, and even economically possible.

Near the top of my list are power levelers.  Leveling and stabilizing an RV using leveling blocks or digging holes is a laborious, messy, and time consuming task.   Fully automatic levelers do it all at the touch of a button.   Once you activate the "Extend" feature, the coach automatically levels itself. The leveling jacks are extended and hydraulically adjusted until the unit is level.  A manual mode allows you to change the positions of each jack, a useful option if you need to raise one wheel to change a tire.   Hydraulic or electric levelers without the automatic feature require the owner to adjust each jack using a toggle switch or lever on the control panel until the unit is level.  Clearly, the automatic option is the most convenient but any power leveling system is a lot better than none. When it comes time to break camp, moving the switch for the automatic system to "Retract" retracts the jacks and prepares the chassis for the road.   Without the automatic feature the owner has to use the toggle switches for each jack to retract them.  In all cases, you should get out and look beneath your rig to make sure the jacks are fully retracted before you attempt to move it.   Adding hydraulic levelers to an existing unit is usually possible, but the high cost ($2500-$3000 plus installation) is a deterrent for most people.  We kind of "eased in" to having automatic levelers.   A Pace Arrow Class A we had a few years ago included a kind of leveling (but not stabilizing) via the air bags in the suspension.  Then our luxurious Holiday Rambler had automatic levelers and I have to say I've really got to like them.  Even to the point of wondering how I ever got along without them.  I've been in places where they lifted the rear wheels clear off the ground to get the body level!   I don't recommend doing that.   Always block the front wheels with chocks.  When the back wheels are lifted off the ground, the parking brake is of no use since it only locks the rear brakes.   If any wheels are lifted off the ground, try to find a more level spot if possible.  Levelers also stabilize the coach, which leveling blocks do not do.  The use of leveling blocks can make the body level, but wind and movement inside the coach will still cause it to rock on the suspension.  Levelers are connected directly to the frame and put the coach in direct contact with the ground so it doesn't bounce on its springs.  Hydraulic levelers provide a convenience beyond saving the labor of working with leveling blocks.  You can level your rig quickly when  you arrive in camp without having to get out, a feature that is especially welcome in inclement weather.  Levelers are one of the luxury options that, at least in my mind, are close to being a necesity.

Automatic electric steps add a measure of convenience.  In normal mode they automatically extend whenever the door is opened and retract when it is closed.  An override switch allows the steps remain extended or retracted as long as you like while in camp.  They usually have a lock out that prevents the engine from being started while the step is extended.   Electric steps can replace the manual steps on some RVs.  Plan to pay about $500 plus installation.  Extending a manual step doesn't require a whole lot of effort.  The benefits of an electric step are mostly found in the convenience of having it move into place automatically when you open the door.  This feature is especially nice when the ground is uneven or muddy and getting out of the vehicle to manually open the steps wouldn't be much fun.  Electric steps usually have lights that come on automatically when the step is extended, adding a measure of convenience and safety at night.  I have made it a point to convert my step lights to LEDs to conserve battery power when leaving the step out in camp.  While clearly not necessary for most of us, electric steps are a luxury item that adds convenience and, if you happen to have a disability that makes it hard to bend over to open or close the manual step, a pretty essential feature.

Automatic transfer switches take care of switching from shore to generator power whenever the generator is started instead of having to plug the shore power cord into the generator receptacle. Prices range from about $50 - $300 plus installation.   Kind of a lot to pay to avoid plugging in and unplugging a power cord, but it is much appreciated in bad weather and avoids the embarassment of calling a service tech for a "generator problem" when you forget to switch the cable.  Once again, convenience is the watch word.

Inverters.   Inverters are gaining popularity for providing 120 volt AC power from batteries so you can use your microwave or enjoy your entertainment system without having to run the generator.  Though far from being standard equipment yet, they are showing up on more and more units.  I thought I was being quite innovative when I installed one in an RV that lacked a 120 volt generator about twenty five years ago before they were offered on any factory units.  Just seemed like a good idea at the time.  Shortly after that I began seeing them in high end vehicles and now they are showing up on many units.

Automatic ice makers are small freezers with a connection to the RV's fresh water system to automatically keep the internal ice bin full.   Of course you can make ice cubes in the freezer in your RV refrigerator, but you have to fill the trays yourself and you it can take along time to make enough ice to meet your needs.  An automatic ice maker works like the one in your fridge at home, turning out ice cubes until the bin is full, then shutting itself off until you remove some of the ice.   Not cheap. Figure around $600 plus installation if your rig doesn't already have one.  There are portable ice makers too, with claims of around 25 #s of ice per day.  Portable ice makers can be found for around $150 or so.

Dishwashers are still fairly rare in RVs but are gaining acceptance.   They usually take the form of a drawer that often replaces the gas oven (which in turn has been replaced by a microwave/convection oven).

Washers and dryers are fairly common in large luxury RVs and appeal to folks who go full timing or work camping.  They aren't particularly practical for boondocking because of the water consumption, but having a dryer to toss wet clothing into if you get caught in the rain can be handy.  If you have washer and dryer be sure to use them once a month or so to keep them in good working order.  Allowing them to sit unused for long periods is an invitation to premature failure.

Trash compactors are found in some luxury RVs but in my experience most RVs don't even have a waste basket or a good place to put one, let alone a trash compactor.  Seems like a kind of natural addition since space is at such a premium.  Being able to pack the trash down so it doesn't take up so much room seems like a good idea.  Of course you can always stomp your trash down to compact it!

Upgraded mattresses these days even include the famous "Sleep Number Bed" in sizes made for RVs.   The mattresses in many standard level coaches are minimal at best and often break down faster than you would hope.  Replacing a poor or worn out mattress or even adding a nice memory foam topper will add a lot of luxury to your sleep with little effort (except for paying for it!).

Hmmmmm.  I'm seeing a trend here.   Seems like we all like features that do the work for us or at least make things more convenient or more comfortable. The list continues...

Satellite TV receivers come in several forms, ranging from portable dishes you set up outside your RV to top of the line roof mounted dome units that even realign themselves automatically as you drive, allowing your passengers to watch satellite programs on the road.  In between are roof mounted dishes you align manually in camp.  You need a subscription to one of the satellite TV services in order to use them.

Home theater systems are finding their way into RVs.  Flat LCD screen TVs are lighter and have a smaller footprint than older CRT models, making big screens feasible in RVs.  Powerful sound systems, some with computer programs what measure and compensate for acoustical defects produce near theater-quality surround sound experiences.  Satellite receivers let you get programming virtually anywhere.  There both manual and automatic satellite dishes.   Some automatic dishes can even be used while in motion.  Home theater systems enhance any RV entertainment system to increase performance and enhance the viewing/listening pleasure.  You may be able to adapt residential components for use in an RV, but take care in mounting them to make sure they are secure, and, when possible, isolated from road vibrations.  Systems designed for RV use are "hardened" to withstand RV conditions (vibration, temperature swings, etc).   Sometimes just upgrading your speakers or adding additional speakers will greatly improve the sound of an RV entertainment system.  Upgrading old, heavy, bulky CRT televisions to new flat panel models usually allows you to have a bigger, clearer screen for improved viewing pleasure, reduces weight, and reduces energy consumption.   It might also give you more room to install additional components, such as audio amplifiers, VHS, and DVD players.  Sound bars are a really easy and fairly inexpensive way to upgrade the audio on your TV.  Some, like Sceptre brand TVs and sound bars have all the controls for both on a single remote.

Exterior entertainment systems let you enjoy audio-visual presentations out on your "patio".  The earliest and least expensive versions were simply radios or radio/cassette players.  These days you will see big screen TVs and Surround Sound speaker systems.  You can entertain the whole camp with some of these.  Just be sure the whole camp WANTS to be entertained when you turn it on and turn it up!

Closely related to entertainment systems are computer and Internet access.   The hot spot feature on most smart phones can give you Internet anywhere there is cell coverage.  Speaking of cell coverage, cell phone booster systems can greatly improve your range -- if you are willing able to pay several hundred bucks to acquire them.

Exterior kitchens may include a sink, small refrigerator, stove, and BBQ grill.  These compact kitchens usually slide or swing out from an exterior cabinet under your patio awning and provide all the facilities you need for outdoor dining.  A simplified version is just an outdoor BBQ, but even that adds convenience.

A second trend: we like our amusements and entertainments.

Slide outs began as options on luxury RVs and are rapidly becoming standard equipment.  When they first came out I saw companies offering conversions to add slide outs to existing units, but the high cost has made it diminishing market.  The last time I checked adding a single 14' slide out to an existing RV would cost close to $30,000, usually making it way more cost effective to trade up to a unit that already has slide outs -- and trading up would avoid possible engineering failures for adding a slide-out to a unit that was never designed to accommodate the extra weight or leverage.

More luxuries turned standard equipment.  Once considered high end luxuries, on board generators are pretty much standard equipment on most Class A and many Class C motorhomes. They are still often optional on Class B motorhomes and many travel trailers. Today's advanced portable generators offer portable power in a light weight, quiet, fuel-efficient package.   Portable generators are not quite as convenient as on board generators.   On board generators usually have electric starters and can be turned on and off from inside the RV at the flip of a switch.  You will usually want to set up your portable generator some distance from your RV or tent (but not near anyone else's).  You have to unload it and they usually have a rope pull starter although electric starters are options on some.  Then you just need to run your RV shore power cord to the generator and you're in business.  Microwave ovens were once luxury options, but are now pretty much standard equipment on most newer RVs.   Fortunately, they can usually be added for a few hundred dollars if your RV doesn't yet have one.  Roof air conditioners have become common as standard features on most motorhomes and travel trailers.  Adding an air conditioner to an RV that doesn't have one is quite expensive.  The units themselves run around $700-$1000 plus installation.  If you are camping with full hookups you can usually take advantage of them even if you don't have a generator.  Some large units with two roof air conditioners may require 50 amp power to run both units at the same time.  Vehicles equipped with 30 amp systems can probably only run one AC at a time.  These units will usually have a switch that selects which AC gets power at any given time so you can manually switch them back and forth to keep the whole RV cool.   A fancier and more expensive setup is a timed switch that automatically switches between the two units.  If you plan to run an air conditioner using a portable generator, choose one with at least 2,000 - 2,500 watts output. Most on board units are at least 4,000 watts.   Believe it or not, showers and toilets were once luxury options.  Early units relied on a "Porta-potty" when boondocking or to avoid trips to the campground restrooms.  Almost all motorhomes and travel trailers these days are also equipped with a hot water heater and have showers.  Some even have small bath tubs.  I've even seen custom units with hot tubs!

Awnings are standard features on many RVs but there are always luxury options you can choose for an upgrade.   Power awnings open and close at the touch of a button.   Rain and wind sensors can automatically close power awnings before they are damaged by bad weather.   Many awning accessories are available to improve convenience.  De-flappers reduce noise and potential tearing from wind; light strings can be attached to the accessory slot in the awning rail to illuminate your "patio" at night; screens and privacy curtains can turn the awning into an outside room; 12-volt fans can create a cooling, artificial breeze on hot days; on REALLY hot days you can add a mist system.  Recently I've seen a fancy, color-changing LED rope light for RV awnings.  They are kind of pricey (around $100) but provide a variety of colors for different moods and even have a hand held remote control.

Powered roof vents are a nice addition to just about any RV.  Standard roof vents are just a screened and domed opening to allow warm air to escape.  You'll be surprised how much cooler it can be in an RV with the roof vents and a couple of windows open.  Since heat rises, the hot air will exit through the roof vent, drawing (hopefully) cooler air in through the open windows.  Just the movement of air through the interior makes it feel cooler even if the air coming in isn't.  Powered roof vents usually have two-way fans that can either expel hot or foul air or smoke or draw in cool air.  Universal fan kits are available to add a small fan to almost any existing vent.  Of course you'll need to run 12-volt power from somewhere.  Fancier roof vents, like the Fantastic brand units, have large, 10-12", multi-blade fans. Available upgrades include power raising and lowering of the dome, a thermostat, and even a rain sensor to close the dome if it rains while you're away from your RV.  Thermostats are a popular option, allowing you to set the temperature at which the fan will turn off so when it cools down at night you don't need have to get up to shut it off or wake up freezing.  Remote controls are also available for some models so you can manage them from the comfort of your couch or bed and also not have to drag out a step stool to reach the controls when they're mounted on high ceilings.

Washers and dryers, as previously mentioned, are usually only found in large, high-end motorhomes and trailers but add an almost residential capability for anyone living in their RV for extended periods.   We didn't seek his option, but since it came with one large RV, we have found it useful.  If nothing else, being able to dry rain-soaked clothing between activities is a god-send.  There are both stackable washer/dryers and combinations that put the washer and dryer in a single unit.   The combos obviously take up less floor space and usually weigh less, but you have to wash AND dry a load before you can start the next one instead of putting a load in the dryer and starting the next load in the washer. Using your washer will consume significant amounts of fresh water and quickly fill your holding tanks when dry camping, so be frugal in their use.  They are much more practical when staying in campgrounds with full hookups.  BTW, if you have washer and dryer, be sure to use them regularly.  Disuse allows them to deteriorate and you will find they don't work right when you do need them.

Central vacuum cleaners are sometimes found on high end units.   The motor and bags are built in and you use a long hose with attachments to clean your unit from stem to stern.  While this provides a level of convenience, I found a simple canister vacuum more than adequate and far less expensive.  And it takes up about the same cabinet space as you would have to sacrifice to install a central system.  The shorter hose of the canister vacuum is easier to store and easier to handle.  I have an older Kenmore cannister that includes a power vacuum head so it is nearly as powerful as an upright without the added weight and space.

Outside kitchens are gaining popularity.   Some are fairly complete kitchens built into the side or rear of the RV.  Smaller versions occupy an exterior storage compartment in basement model coaches. Adding a complete outside kitchen to an existing RV would probably cost a lot more than its worth, but you might be able to set up basic functionality in an existing outside storage compartment.  The convenience of having kitchen facilities right there under your patio awning makes serving you and your guests fun and easy.  Lacking a cabinet where you could install kitchen facilities you might use a "camp kitchen" or a chuck box meant for tent camping to organize your stove, grill, cooler and other items for outside use.

And don't forget cordless tools.  These modern wonders can add a lot of convenience to camping.  A cordless drill can be used for many tasks around a modern RV.  One of my favorites is a small 4.5 volt screwdriver from Worx.  It has an extendable shaft which makes it handy for reaching into deep spaces where shorter, fatter drill/drivers won't fit.  I found it surprisingly powerful and the battery quite adequate, especially for such a small unit.  With a few hex-shank drills it can even be used as a drill.

You have earned a little luxury! Enjoy!

Solo Camping

Although for most folks camping is a group activity, some people do enjoy solo camping from time to time.  If you take appropriate precautions for your own safety it can be very relaxing to get away all by yourself for a while. There is no reason you can't go RVing or camping by yourself, but it is usually more fun -- and safer -- if you have someone to share it with.  The famous mountain men of the old west spent months or even years by themselves, living off the land.   Of course they had a lot more preparation, wilderness training, and survival skills than most of us do today.  I strongly urge you NOT to participate in any high risk activities solo.  Even Surivorman Les Stroud always has a safety team standing by if he doesn't show up where he is supposed to on time.

There are some risks associated with solo camping, especially if you are also involved in other activities, like hiking or OHV riding.   There is a very dramatic story of Aron Ralston, who went hiking alone in the slot canyons in southern Utah in 2003.  He fell into a gorge and one arm was pinned by an 800 pound boulder that fell on him.  Eventually, after 5 days and 7 hours, he had to cut off his own dead arm using a dull multi-tool to escape.   If he had tried to amputate is arm earlier he would have bled to death.  If he had waited, he would have died of shock and/or exposure.  Unfortunately, he had failed to follow the basic rules of solo camping.  He had not left good information about where he was going and when he would be back so it took longer than it should have before anyone knew he was missing and even longer to figure out where to look for him. When he finally got free it was a family vacationing from the Netherlands, not intentional rescuers, who found him and helped him get to safety.

Following the basic rules of solo camping can add a measure of safety to your outing.   First of all, always let someone know where you are going, when you are going, and when you should return. That way, if something happens, like it did to the young man mentioned above, someone will know to come looking for you and will know where to start looking.  Once you have shared your plans, stick to them.  It won't do you any good at all if you suddenly decided on a different destination.   If you do have to change your plans, notify whoever you shared your original plans with.   If that isn't feasible, at least stop by the local ranger or sheriff station for your new destination and let them know what you're up to and when you expect to be back.  Also tell them what your original plans were so they'll know where people may start looking for you.  Then, be sure to stop by on your way back to let them know you got out OK.  When going solo, make sure you are in good health before you start.   If you start out already ill or injured, your chances of having a successful adventure are severely reduced. Illness and injury can affect your judgement as well as limit your physical capabilities.  Be sure to carry plenty of water and bring along a good first aid kit.   If you require any prescription medications, make sure you have more than enough with you to last throughout your trip . Avoid particularly dangerous situations and activities.  Solo rock climbing or spelunking, for example, would be very bad ideas.

NEVER go dirt biking or ATV or horseback riding or similar activities alone.   The potential for equipment failure or a serious injury during these adventures is too high to ignore.   Even excellent expert dirt bikers have found themselves in situations where they need help.   A good friend of mine and an excellent, experienced rider was taking a leisurely solo jaunt on his dirt bike in a desert area he was very familiar with.  He wisely avoided all the "black diamond" (most difficult) trails.   He was badly injured when his front wheel unexpectedly washed out in a soft spot and he crashed on an ordinary, level dirt road.  All alone he had to pick up his bike, start it, ride back to his truck, load the bike, and drive some 150 miles home.  All this with 3 broken ribs, a broken collar bone, a broken wrist and a sprained ankle.   I doubt if that is anyone's idea of a good time.   If he had been riding with a buddy, he would have at least has someone to help him pick up his bike and get him home.  If his injuries had been more serious he would have had someone assist him and/or to go for help.  He also had ignored the basic rule and had not left good information about where he was going and when he should be back. If his injuries had been more serious when he was by himself, he might have died before anyone would have found him.   My own grown son, who is a very experienced and expert rider, had a near miss on a solo ride on a familiar canyon trail near his home.  It was raining and he was being extra careful as the trail went over a large boulder in the middle of a scree slope -- TOO careful, as he lacked the momentum to carry him safely to the other side.   He stalled and the bike tipped off the boulder and he and the bike both began siding down the scree.  Only a fortuitous outcropping of shrubbery kept both him and the bike from sliding all the way to the bottom of the mountain. Fortunately he was not seriously injured and was able to bulldog the bike across the scree and eventually made his way down to a forest service road in the valley below.  I don't think he'll EVER go riding alone again!

If you choose to go camping solo, leave word where you're going and when you expect to be back. Make sure you and all your equipment is in good condition.   Carry plenty of water, more than you think you'll need for the time you expect to be gone.   Carry a first aid kit and some high energy food. Then stay alert and be careful.   Don't take any unnecessary risks.  Bring your cell phone. While cell phones may not work in a lot of remote places, it is sometimes surprising where you can get a signal. Some areas with limited capabilities have emergency only service.   About the only number you can use is '911'.   A hand held Ham, CB, FRS, or GMRS radio might also provide emergency communications, but they normally work only "line of sight" between your transmitter and a receiver and have limited range.  If you're in a mountainous area, you may have to hike to the top of a peak to be able to reach some receivers.  It will also be helpful to learn what channels or frequencies might be monitored by local law enforcement or rangers.  CB channel 9 is the standard emergency channel;  channel 19 is the traditional trucker's channel, and channel 13 was adopted as the RV channel.  These are my no means hard and fast rules, but they may give you a place to start instead of blindly going through all 40 channels.  Modern technology offers emergency beacons you can activate to notify friends and/or authorities if you have a serious problem and provides them with GPS coordinates to help them find you.  They can often be set for alerts to be sent via text or email to a predetermined list of recipients keeping them apprised of your progress and alerting them if you have an emergency and need  help.  Carry a signal mirror.  I also like to bring along a flashlight that flashes SOS.  It can be set to continuously signal for help even when I'm resting.

Camp safe!

Group Camping

Group camping is probably one of the most popular forms of camping after family camping.   Part of the fun of camping is sharing activities with our friends and family.  About the only difference between family camping and group camping is that the family camping group usually consists of people related by blood or marriage.  Group camping folks are connected by common interests and/or friendship.  Group camping makes campfires more fun and expands our options. There is also a measure of security that comes with group camping. Y ou can participate in a group camp as individuals or as families.  Our Desert Rat group in California often included families with at least 3 generations present as well as some individuals who's families had no interest in camping or dirt biking.  All were welcome and all had a good time.  Those who didn't ride spent a lot of quality time visiting with each other in camp.  People from individual campsites often congregate at commercial campgrounds for both planned and spontaneous group activities. 

Group camping requires a little more planning and coordination than solo or family camping. For one thing, you need to know how large the group is going to be so you can make sure you have sufficient camp space for everyone.  Family camping often involves just your immediate family; group camping can include many people.  We've as many as 175 people show up for our annual Turkey In The Dirt Thanksgiving Potluck.

If you're headed to a developed campground you will need to reserve a group site or several individual sites.  If you have to get individual sites you will want to try to get them all together or at least as close as possible.   Then you'll probably want to designate one of the sites as your "primary" site or "HQ" (headquarters) where you gather for coordination and shared campfire activities.  Having access to a well developed group site will offer several advantages.  There will usually be a large central gathering area with a permanent fire pit, maybe some rustic seating, and sometimes even a bowery or pavilion for sun and rain protection. 

If you're boondocking or camping in a primitive area, you will need to scout it out ahead of time and get there early to stake out your territory and reserve enough space for everyone you expect to join you.  Some primitive areas are used enough that they have developed defacto camp sites with rock fire rings.  Try to use existing areas when possible.  Not only will it be more environmentally friendly than stomping out a new site, you will probably find it helpful that someone else has already found the most levels spots for RVs, aleady cleared pads for tents, and probably created a central rock fire ring.   We've found the old wagon train evening format ("circle the wagons") a good one for primitive camp sites.  Arrange your RVs and/or tents around a central fire pit and group meeting area.  That way no one is very far from the campfire or each other.  You want spacing that respects privacy while facilitating group participation.

Pot luck dinners are a fun thing to do in a group.  True pot luck dinners are often spontaneous and everyone just brings whatever they may have on hand.  You can pull one together anytime and it will usually be quite successful.   If you are a little bit of a control freak or have specific menus in mind or expect a large number of participants, you can organize your pot luck dinners ahead of time.  That is what we always did for our annual "Turkey In The Dirt" dirt bike outings at Thanksgiving. One year we had 142 RSVPs and 175 people show up.   With a group that large, a spontaneous pot luck probably wouldn't work as well as making at least some assignments ahead of time so you don't end up with 17 green bean casseroles and no mashed potatotes!

Group campfires are always fun.   For one thing, it spreads out the work of building and maintaining the campfire and shares the cost of the wood.  More importantly, it is an opportunity for great social activities like storytelling and sing-a-longs.   Roasting hot dogs and marshmallows and making S'mores are long time campfire traditions.  If you've tired of that you might want to organize a Dutch oven dinner or try your hand at other forms of campfire cooking.  Always try to make room around the fire for everyone in your group.  At the end of the evening, make sure the fire is out and the camp chairs are all properly stored or at least folded flat so an evening breeze doesn't blow them into the fire pit.  The hot coals buried beneath a fire that has been "put out" may still hold enough heat to melt or even ignite camp chairs.  If you're the last one to leave a group campfire, store your own chairs and make sure any that anyone else has left behind are moved away from the fire ring and are folded flat.   I've seen aluminum frames melted into puddles and the plastic webbing vaporized by morning when chairs that weren't put away blew into the fire pit overnight.

When camping in certain open areas of the Mojave Desert where shooting was allowed, we often did a little skeet shooting in the evenings.   Firearms aren't for everyone, but it was a fun activity for those who chose to participate.  It may also have a side effect regarding security since it is obviously an armed camp to anyone within earshot and that might deter would be protagonists.  If you choose such an activity, be sure to exercise proper range and firearm procedures to ensure everyone's safety.

Many kinds of activities lend themselves to group participation.  We very much enjoy group dirt bike rides.   Someone volunteers or is appointed as the ride leader and chooses a route and/or destination.  Another competent rider volunteers or is chosen to ride "sweep" and make sure no one gets lost or left behind on the trail.   The same thing can be done with ATVs or UTVs (side-by-sides). There are many campground activities for the less motor minded too:   horseshoes, touch football, frisbee, volleyball, badminton, and lawn darts come quickly to mind as common and popular things to do when camping.   Basketball may be an option at a developed campground as some do have basketball courts.  We've found skeet shooting to be a fun group activity for our desert outings.   Just make sure you have a safe backstop and have someone keep an eye out for errant travelers who may inadvertently drift into the line of fire.  Skeet shooting may have a hidden benefit:  it may alert potential intruders or persons with ill intent that yours is a competent armed camp and deter them from bothering you.

Group camping lends itself well to any group of people with common interests.  Local Good Sam Club chapters bring together people from the same area, usually with a focus on specific kinds of activities.  Many Good Sam activities focus on service projects or fundraising for adopted charities. RV clubs sponsored by or based on vehicle brands are also common.  In many places you will find dirt bike, ATV. and 4WD clubs to match your choice of vehicle and riding styles.   Rockhounds, birdwatchers, hikers, and history buffs may also have organizations in your area if that is where your interests lie.

Circle the wagons!

Family Camping

Whether you go in a luxury RV or a second hand tent, camping is a fantastic family activity.   Next to Boy Scout troops, families are probably the largest demographic for camping.   We started camping with our kids when they were babies.   A couple of weeks ago we spent a weekend with our grown son, his wife and their baby.  Everyone had a wonderful time.  We had originally planned to take our truck camper up into a local canyon that is ablaze with fall colors but our truck developed mechanical problems and we had to fall back to tent camping.  The canyon roads were not compatible with our 40' Class A motorhome.  The campground was already partially closed for winter and the restrooms were shut down but we still had a fun time.  For a group that has been mostly camping in motorhomes for the last 30 years or so, we did pretty well with tent camping.  I even practiced what I preach and started our campfire with flint and steel. The evening was cool -- perfect campfire weather -- and we were quit comfortable sleeping in our tents.

Family camping in our RV and riding our dirt bikes about once a month was a mainstay activity for our family of 8 when our 6 kids were growing up.  Now that the kids are grown and we're semi-retired, things have slowed down a bit, but we still enjoy camping with our extended family.   We spent a wonderful, non-dirt biking camp out with one of our daughters and her husband and his family in accordance with their summer traditions last year and had a great time.  It was really fun to see and even become part of their camping traditions for a while.

Family camping doesn't have to be restricted to just your immediate family.  We've been to a couple of extended family reunions that were held at campgrounds.  There were dozens of motorhomes and travel trailers from several states containing multiple generations of extended family.   Activities included sharing family history and an exchange of home made gifts as well as potlucks and campfires.  I still use the knitted napkin holder in our motorhome that we got at one of these.  It was really fun to meet some of the relatives I'd only heard about before but never met and listen first hand to adventures that my dad had alluded to over the years.

Sometimes it is nice not to have a lot of planned activities.  Most of our family outings over the years have been dirt bike trips and everyone was usually anxious to hit the trails.   But our most recent tent camping trip with our son and his little family we had an open schedule and just took our time with everything. It was quite relaxing.  We arrived at our campsite early enough that we had plenty of light to set up our tents without any rush.  We heated up some of Marilyn's Marvelous Mojave Mild chili on our trusty Coleman stove and enjoyed a leisurely dinner around the campfire. Since our campsite was in a forested area and we had two huge pine trees right in our site, we didn't get in much star gazing.  Star gazing is better in the desert; too many trees in forested areas. The next day we slept in and then enjoyed a great breakfast.   Making it together in camp was whole lot more fun than fixing breakfast at home.   Even routine tasks like cooking become a fun, shared adventure in camp.  Why is it pancakes seem to taste better when camping?   We were able to spend a lot of time just talking and catching up on what both families had been doing and discussing upcoming events.  A couple of chipmunks that lived in the pine trees in our camp provided lots of active entertainment.  I suspect they were as amused at us as we were with them.

Family dinners are a fairly frequent occurrence for us, as I'm sure they are for many people, and these always involve a lot of shared kitchen responsibilities.   However, family meals while camping take on a whole different ambiance.   The fun of cooking outdoors and getting creative with the meals gives things a whole new meaning.  As much as we all like having family over for meals, preparing those meals at home and cleaning up afterwards can be a lot of work, work that is tedious and tiring. Preparing meals in camp might actually be even more work, but if nothing else, the novelty of it makes it more fun.  My wife and daughter-in-law were giddy as a couple of school girls as they prepared our meals during our tent camping trip on the Nebo Loop Scenic Byway in Payson Canyon. They even seemed to enjoy cleaning up afterwards!  And us guys helped out too, believe it or not!   Whenever you go camping you need share responsibilities for routine tasks.  Guys may not be handy in the kitchen, but most can manage an outdoor BBQ well enough to grill some burgers, hot dogs, and/or steaks and maybe even do some corn and baked potatoes and even the most macho dude shouldn't be above helping out with the dishes,  especially when  camping.

Campfires are always a good time for conversations, reminiscing, storytelling, and singing songs. This is particularly true for family campfires. Even if all you do is sit and let yourselves be hypnotized by the flames, there is a kind of bonding that seems to take place.  Campfires are especially enjoyable on cooler evenings when you actually need the glowing fire to take the chill off, but we found them a lot of fun even on warm nights in the desert.   Everyone can do their part in preparing and maintaining the fire and in participating in campfire activities.   Whether recounting the day's activities or sharing tall tales, campfire story-telling is always enjoyable and often fascinating.

Our tent trip took advantage of the amazing fall colors along the Nebo Loop Scenic Byway in Utah County, Utah near our home.   Maples at the lower part of the canyon were bright red.  Higher up, the aspens were vibrant yellow, all contrasted with the vivid greens of evergreen trees.   The Nebo Loop winds up through Payson Canyon in the Wasatch Mountains, with spectacular views of Utah Valley and Mount Nebo, the highest peak in the Wasatch Range.  We were especially glad to finally make this trip.  We've lived within 5 miles of the Payson end of the Nebo Loop for more than 6 years, and for one reason or another, never got around to making the drive.  Getting together with other family members was an excellent reason and sharing the beauty with them enhanced the experience. Way too often we ignore glorious opportunities right in our own back yards, sometimes until it is too late.   Gather up your family and head for the hills (or the lake or the beach or the desert) as often as you can.  Don't wait for an excuse to go -- make one up if you have to!  Just going is reason enough.

Family camping trips are always a good opportunity for meaningful conversations and even though our kids now have kids of their own, still offer many teaching moments.   These days it is just as likely that my kids will be the ones doing the teaching, not only for their own kids, but in sharing new skills with Grandma and Grandpa as well.   But that doesn't mean the senior citizens should just sit back.   There are still some things we can teach the younger generations, especially if we remain active and alert to learning new things ourselves.   I thoroughly enjoyed a story attributed to Mark Twain that says when he was 14 years old his father was the most ignorant man he knew but by the time he was 21 he was amazed at how much the old man had learned in 7 years!

Family boating activities can be as fun and forge as many bonds as camping.  As with RVing, OHVing, or camping, boating gets you out of the daily grind and lets you share in some special activities.  Sailboats are especially good places for sharing fun and responsibilities.  Motor boats can be exciting and invigorating.  I sometimes wonder if the fact that our bodies are around 70% water accounts for at least some of our attraction to the water.

Family camping begins long before you reach the campground or even hit the road.  Start by involving the whole family in choosing a destination and/or route, scheduling, and planning menus and activities.  Let each one do their part in preparing gear and packing provisions.   All but the youngest campers or others with special circumstances should be responsible for their own clothing and equipment.  We made sure our kids learned to prepare their own dirt bikes and gear for each trip. It worked well enough that when my oldest daughter began racing Women's Desert Expert Class she did many of the races entirely on her own, providing not only her own camp support but her own bike maintenance and repairs!   And, by the way, this same daughter was also a beauty pageant contestant one afternoon after a morning of desert racing!   Make sure everyone has assigned tasks to help set up camp once you arrive and throughout your stay.   Everyone is going to be anxious to go about planned activities or just begin exploring, but overall things will go a lot smoother if you take time to set up camp together BEFORE starting any adventures.  Then everyone can relax and have a good time.

Trip out together!

Installing RV Awnings

RV awnings come in a variety of awning styles, ranging from "bag awnings" that are rolled up and carried inside the RV to elaborate power awnings with wind sensors that automatically roll them up if the wind kicks up.  As you might expect, there is also a wide range of prices.  RVs with slide outs often have automatic awnings installed over each slide that roll out when the slide is extended. Window awnings are nice to have.  They provide shade and can be used to prevent light rain from entering open windows letting you enjoy the fresh air during a mild rain storm.   Stand alone awnings are commonly referred to as "canopies" and aren't attached to an RV.

Permanently mounted manual awnings are the most popular, although power awnings as standard equipment are catching up.  Manual awnings are, of course, less expensive than the power version.   Both roll up against the top of the side of your RV and have arms that fasten to brackets near the top and bottom of the side wall.  They can usually be used either with the arms still attached to the bottom brackets or in "patio mode", where the arms are moved out to a vertical position and staked to the ground.  When still attached to the brackets, the arms form an angle from the roller on the outer edge of the awning to the bottom brackets, sometimes creating an obstacle that people bump their heads on.  When using the arms in patio mode they should be staked down to prevent unwanted movement.   In patio mode the supports are vertical at each corner.  To further stabilize patio awnings, you can install an awning strap.  This wide nylon strap is secured on either end by corkscrew shaped anchors that screw into the ground.  The strap wraps over about the middle of the awning from the front of the vehicle to the back to hold it down.  Another useful accessory for patio awnings is pair of "de-flappers".  These devices clamp to the awning fabric and fasten to the end rafters to reduce flapping of the fabric in mild breezes. I 've seen two different types, one that fastens around the end rafters with velcro straps and another with rigid plastic clamps that are tightened around the awning arm.  Long awnings tend to sag in the middle and benefit greatly from an extra (optional) support in the middle.  A set of optional supports marketed under the name "Awnbrella" can be used to lift the awning and stretch it kind of like an umbrella to give it a form that lets rain run off without puddling.   Another good helper is an awning clamp that wraps around the awnings to prevent them from unrolling in the wind during travel.  Having experienced an awning coming unrolled on the freeway, I have a great appreciation for awning clamps.  Manual awnings usually have an awning wand to snag a loop in the middle of the rolled up awning to pull it open.  The one that typically comes with the awning is a rod about 5/16" in diameter and about 3 1/2' long.  It has a loop on one end that serves as a handle and the other end has about an inch bent at a right angle to slip into the awning loop.  If you've lost yours or just want something that isn't so big to carry around and keep track of you can buy telescoping versions that push down to about a foot long and can be stored in one of the galley drawers along with kitchen utensils.  I tried one of these and the tip came off the first time I used it.  The telescoping awning hook is a really good idea -- if it were better made!  While the telescoping feature makes it easy to store it also means you can't use it to push the lock on the awning roller or use it to push bedding into place on corner and over-the-cab beds.

Power awnings are becoming more popular but are still fairly pricey.   Power awnings can be extended or retracted at the touch of a button.   They also come with options for rain and wind sensors to automatically retract them when rain or wind is detected and with remote controls so you can operate them from the comfort of your camp chair or even some distance away if the wind kicks up unexpectedly or from inside your RV if you don't want to go out in the rain!  If you do roll them up when it is raining, be sure to open them up and let them dry out as soon as  you can to prevent mold and mildew from destroying the fabric.

Bag awnings are usually less expensive but aren't quite as convenient to use.  They can also be used on more than one vehicle by simply installing an awning rail on each vehicle.  Bag awnings have one edge that attaches to the awning rail on the RV.  The outside edge is supported by 2 or more poles like tent poles and secured by guy ropes, like a tent.

Window awnings also use the same type of rail as other awnings but the rail is screwed into the framework around the window, directly above the top exterior window frame.  Window awnings, like permanently attached patio awnings, have attached arms, but no top brackets.   The top of the arms are attached to the roller. You will need to install bottom brackets.  Arms on window awnings are fixed length, so you have to install the brackets wherever the end of the arm strikes the sidewall when the awning is open.  Sometimes this will be in line with the framework around the window, but if not, simply securing the brackets through the RV "skin" with pop rivets or short metal screws is usually sufficient. You will also need to install a little bracket to fasten the awning pull strap to to hold the open awning in place.

To install any awning you will need an awning rail attached to the vehicle.  For patio awnings, this is usually attached just below or sometimes behind the drip rail at the top of the side wall. You need a sturdy support behind the thin wall paneling to screw the rail to.  This is the most critical factor for installing awnings.   Before installing any awning, make sure there is sufficient room above your door so the door will open without hitting the extended awning.  In addition to the awning rail itself you will need dozens of self-tapping screws and enough butyl tape (sometimes called "dum dum tape" to match the length of the awning rail.  The tape seals the rail to the vehicle and seals around the screws to prevent rain intrusion into the side wall.  A power drill/driver is pretty much required, although you could get by installing the screws by hand if you drill pilot holes first.  Make sure you don't kink or pinch the opening of the rail.   Once the rail is in place, you can slide the awning into it. For bag awnings, installation is done.  All that is left is unrolling the awning and installing and staking down the poles.  For permanently mounted awnings you may want to put a short screw through the mounting rib that slides into the rail and into the rail to keep the awning from sliding forward and back.  The next step for permanently mounted awnings is to install the top brackets.  Make sure the awning is fully retracted and mark the location for the brackets on each end. Drill pilot holes for the mounting screws, which are much larger than the self-tappers used to secure the rail. Typically these are like 1/4" lag screws.  Once the top brackets are securely screwed on, using a level to make sure the arms are vertical, mark the location for the bottom brackets.   The legs are adjustable and you must find a place on the wall with solid backing to fasten the brackets to.  This usually is at floor line.   Once you have decided where to put the brackets, make sure the arms are straight up and down, mark the holes, drill pilot holes, and install the screws.   Your awning should now be ready to use.

For power awnings you'll need to install the wiring.  An interior switch will control extending and retracting the awning.  There may also be a remote control that let's you stand outside and control the awning.   You'll have to drill a hole through the side wall to route the wires.  Make sure will have access to the wiring inside the vehicle.  Find a source of power and a place to connect a ground wire and run the wires.  Hiding the wiring inside the bottom shelf of cabinets is way to achieve a clean installation -- and you usually have 12-volt power available in light fixtures you might be table to tap into.   However, keep in mind the motors on the awning will draw significantly higher amperage than lighting.  The best way of wiring the awning is to give it its own circuit and fuse.   Tapping into the wiring for lights may overload the circuit.  Upgrading the fuse to keep it from blowing would allow the existing wiring to overheat, possibly causing a fire. NEVER use a higher amp fuse than a circuit was originally designed for. Doing so turns the wiring into the fuse so the wiring melts before the fuse blows!  Make sure you seal the hole where the wiring goes through the wall using silicone sealer.

 
Some variations for bag awnings.  I found the poles and guy ropes for a bag awning on my enclosed motorcycle trailer were cumbersome and often got in the way when moving my dirt bikes around so I rigged a way to install the poles against the bottom of the trailer.  I simply put large screws into the bottom edge of the side wall at approximately the angle the poles would be when the awning was extended.   The bottom end of the poles slip over these screws instead of resting on the ground.  Then I added eye-bolts close by and used light weight ratchet straps from the eye-bolts to the upper end of the poles at the extended awning roller.  That way the guy ropes and the poles are aligned and mostly out of they way when walking under the awning.

Finally, you could use a canopy and not have to attach it to your RV at all.   Free standing canopies are usually less expensive than attached awnings, but are less convenient to transport and to use.   It could be used next to an RV in lieu of an RV awning.  One possible downside is that a gust of wind might slam it into the RV, damaging both the canopy and the RV.  You can use a free standing canopy with your RV or take it with  you tent camping, so it offers a little more flexibility than an attached RV awning.   Canopies may be self-supporting like the famous E-Z-up models or have to be tied down with guy ropes.  There are even some these days with structure similar to dome tents that are light weight and easy to put together.  A free standing canopy (often called a "dining fly ") can be set up over your picnic table if needed for shade or rain protection.  Many canopies include a center pole for extra headroom.  Dining flys omit the center pole since it would land smack in the middle of the picnic table.

Now you have made the shade!

Building Your Own RV

Building your own RV is certainly not for everyone.  It takes a lot of planning, time, and money.   Why would anyone want to go to all the trouble to build their own RV?   Some people will opt to build their own in an attempt to save money.   Sometimes that works, but unexpected expenses can drive the price up rather quickly.  Most people have no idea what is involved and get some rather unpleasant surprises as they proceed.   Some people may want to build their own RV to implement specific features into the design to meet their needs.  Someone who is extra tall may need higher than standard ceilings, raised countertops, and a longer bed than is available in production models.  You may have a hobby that requires special work space or storage.  Do as much research and planning as you can before you begin.  Small motorhomes can be built into a conventional van.   Larger models will need a bigger truck or bus as a starting point.  No doubt you have seen converted school buses on the road.  Home-made conversions can be ugly or interesting, depending on how skilled the craftsman is and how much he is willing to invest in cosmetics.  I've seen some very "interesting" adaptations, like a VW van given an expanded roof by the addition of a VW beetle body welded to the top.  Sure looked strange!  Other variations include wooden shack like structures on a pickup or heavy duty truck that look like they belong on an Ozark mountaintop instead of the highway.  I've seen photos of a very sleek custom made aluminum "Starstreak" motorhome built on a 1976 Cadillac El Dorado chassis.  This vehicle now lives in the RV Hall of Fame in Elkhart, Indiana.  Be sure to watch the slide show for their Featured Units.  Many of you probably recall the multi-colored school bus used by The Partridge Family on the TV show of the same name.  It was colorful and functional but not what you would call beautiful.

If you have the budget for it, you can, of course, have an RV custom built to your specifications.  Newell and Foretravel both specialize in building customer coaches to spec and many other major manufacturers will work with you to adapt their high end products to meet your needs.  Unfortunately, these units often cost over $1,000,000!

Before attempting to build your own RV consider whether there is already something out there that will meet your needs. There are many different styles of RVs in existence and it may be a lot faster and even cheaper to buy one than to build your own.  Used RVs can often be had for very little money.  You may be able to adapt a factory model to your personal needs fairly easily.  But, if you are determined to build your own, read on!

I have never built my own RV but I did build (or more accurately adapt) my own motorcycle trailer, which has many RV like components.  I purchased a custom made motorcycle trailer from an engineer who had built it for his own use and no longer needed it.  One of the things I really liked was it was built on a 5500# single axle (most single axles trailers are only 3500#).   I also appreciated the sturdy steel frame construction that made it suitable for off road trips. It came with a rear ramp door, counter across the inside of the front over a nice Kennedy tool box.   I added peg board, additional lights and wiring, a water tank, pump, and sink, and eventually even a roof A/C.  I put in shelves and closet rods to store riding gear, a rack for tie downs, and racks to secure my gas cans.  When it was done it was almost a motorcycle shop on wheels!  Building it was almost as much fun as using it and I got a lot of nice compliments from my fellow riders.  Having appropriate tools, equipment, and spare parts on board allowed me to lend assistance to many of my riding companions over the years.

One way to minimize engineering (and cost) is to customize an existing RV to your individual specifications.   Many times it is easier and cheaper to modify an existing unit than to start from scratch.  You may be able to take advantage of fresh water, waste water, propane and electrical systems without having to design and engineer them yourself. 

Your first step is to determine what kind of RV you want to build:   motorhome, truck camper, or trailer. One of the most popular home-made units is the tear drop trailer.   They can be built from scratch and plans are available on the Internet.  In this case you buy an axle and build your own chassis from the ground up.   The next most common conversion is creating a motorhome from an old bus.  I've seen converted school buses, city buses, and Greyhound buses.  Greyhounds or other inter-city buses make the best platforms.   City buses are often geared for lots of stop and go driving which is not always the best configuration for a motorhome you want to go places in but I have seen successful conversions done on old city buses.   Don't know how long they lasted or what kind of gas mileage they got, but they were well built and very functional.  School buses are probably easier to come by, less expensive, and should be an acceptable platform if they've been well maintained.  As mentioned above, you might remember the multi-colored bus on the old TV show "The Partridge Family".   The presence of an existing bathroom on inter-city buses sometimes saves the builder some time and money -- if you're OK with the location of the existing restroom.   If not, it may be an added expense and construction problem to relocate it.   If you don't need lots of room, you might start with a standard cargo or passenger van.  One advantage of using a van, is they usually will fit in your garage.  The venerable Chevy Stepvan is another fairly popular choice with do it yourself motorhome builders.  Its open, boxy shape allows lots of interior design flexibility and stand up head room.   If you want to build a truck camper you're going to most likely have to build it from scratch and you'll need some good plans to ensure structural integrity.  My first motorized camping vehicle was a 1951 Chevy Suburban with minimal modifications.  I added curtains for privacy.  Sleeping bags rolled out on 1/2" foam pads in the back of the vehicle provided beds.  A folding TV tray, a plastic dishpan, and 3-gallon plastic water jug served as both kitchen sink and hand washing basin.  A large Coleman cooler substituted for a fridge.  Eventually we even added a porta-potty.  It wasn't fancy but it sure beat trying to set up a tent in the dark or the wind!  And it wasn't very expensive at all.  Even driving it was fairly cheap.   It had the original Chevy 6 cylinder engine and a manual transmission and, of course, ran on the lowest priced regular gasoline.  As rudimentary as it was, it was a lot warmer and more comfortable and convenient than camping in a tent.  And it didn't require any structural modifications.

Planning is one of the most critical steps. Y ou will want to list all the features you want to have and try out several floor plans. Keep in mind your floor plan may affect what kind of vehicle you choose for the platform and, in turn, what vehicle you get may affect your floor plan.  Allow some flexibility or be willing to make adjustments based on features and limitations of your platform. Some of the basic considerations should include:  how and where you intend to use the completed unit, how many people will be traveling in it, and the ages of the travelers (accommodations for kids may be different than those needed for adults).  If anyone in your family has any disabilities you may need to include accommodations in your design for their special needs.  Your design might also be influenced by any equipment or appliances you may already have.   A fairly good cost-saving way of getting much of what you need for a conversion is to buy a cheap used or salvage travel trailer and use it as a donor for cabinets, appliances, holding tanks, and furniture.

Weight is always a major concern for an RV.   RVs are usually framed with 2x2s, not 2x4s or 2x6s like houses.  Using 2x2s gives you about 4" additional interior space and about half the weight as 2x4s, both significant advantages for an RV.  I've seen an RV built like a house, using 2x4 framing and then using 1/2" sheetrock for interior walls.  Wow!  Was that thing heavy!   It will certainly be sturdy, but I wouldn't want to drive or tow something like very far or very often.  Might be OK for a "tiny house" used for a permanent residence that usually doesn't go anywhere.

Choosing the basic vehicle for your conversion is one of the most important steps.  Price is probably a major factor.  Otherwise you could just have million dollar custom Newell or Foretravel built to your specifications.  You will also want to consider the condition and the brand and model of major components, like the engine and transmission.  Seek vehicles with a drive train for which parts are still readily available.  You shouldn't have any trouble finding parts and service for those with Caterpillar or Cummins power plants and Allison transmissions or for GM, Ford, and Dodge trucks. Greyhound buses usually already have an existing bathroom so that may be an advantage -- IF you are willing to have the bathroom where it already is.   If you have designed your own floor plan with a bathroom somewhere else, already having one won't help and may even make things more difficult. While buses are most frequently chosen as the platforms for home-made motorhomes, other trucks are sometimes used too.  The venerable Chevy "Step Van" provides a sturdy option for smaller motorhomes and may be less expensive than a bus.  You can also be assured that mechanical parts will be available.

Major interior components include cabinets, appliances, plumbing fixtures and furniture.  You might be able to adapt cabinets from a donor vehicle or buy new ones at a home center.   Cabinets from home centers will probably be larger than would normally be used in an RV so you may have to adapt the cabinets or adjust your floor plan to accommodate them.  Residential sinks and toilets are usually too big and too heavy to use in RVs.   It is nice to have a donor vehicle to supply appliances, furniture, plumbing fixtures, and holding tanks.  Purchasing a donor vehicle before you finalize your design allows you to have exact specifications for the construction of cabinets and the installation of appliances and furniture.  The donor vehicle doesn't have to be the same style as the one you're building.  You can salvage lots of useful components from an old travel trailer to build your own motorhome.

Finishing the interior.   Some buses already have finished interior shell walls.   Retired Greyhounds usually do.  School buses are more likely to have naked walls.  If your platform doesn't have finished exterior walls, frame the interior with 2x2 lumber, add insulation (bats or foam panels) and cover with 3/16" or 1/4" paneling.  You might want to use FRP (Fiber Reinforced Plastic) board in the bathroom and kitchen areas.  It is attractive, easy to install, waterproof, and easy to clean.   Insulating interior partitions between living spaces is optional.  While it may help you to maintain comfortable temperatures in your living space if you are only occupying a single area (like the bedroom at night), the main benefit is probably soundproofing.  Given the low cost and the ease of installing insulation during construction, I would opt to put it everywhere I could.   Use 1/4" luan plywood for interior sheeting.   If you like the wood pattern of your interior panels you need no further interior finish. However, for variety or to satisfy personal decor preferences, you could paint or wallpaper the paneling to suit your needs.   If you plan to paint or wallpaper you'll probably want to use smooth paneling, not the kind that is grooved to look like planks.   Even if the lines aren't stamped or grooved, they may still show through paint.  If they are smooth and only painted on they shouldn't affect wallpaper but they might bleed through paint and then you would have to prime the walls with something like Kilz to cover them up before painting.

Floors in an old Greyhound or school bus can probably just be carpeted over.   If the floor is metal and is all there is between you and the road, you might want to build it up a bit to reduce road noise, heat from the exhaust system and the pavement, and improve overall insulation qualities. Accommodating plumbing within the floor can make your rig more usable in winter weather.  This would be especially true if you also run your heat ducts in the same compartments as your plumbing. How you build up the floor depends on whether you will be using the space for plumbing and duct work.   If you are not running plumbing inside the floor, put a vapor barrier directly on the existing floor.  If you want to insulate the floor, add a framework deep enough to accommodate the amount of insulation you want to use.   Then install marine grade plywood. Typical residential sub-floors use particle board.   Because of the stress and the potential for water getting in the particle board, I don't recommend it for RV use.   If it gets wet, from a plumbing leak or rain intrusion, it will crumble. Once your plywood is installed you can install your chosen flooring (carpet, tile, vinyl, laminate). Flooring in factory built RVs is often installed before any cabinets or furniture but it is up to you whether you want to do it that way or not.  It may be easier to replace or upgrade the flooring later if it is not installed under cabinets and you may save a few square feet of flooring material.  Carpet with thick padding will provide extra insulation for heat, cold, and sound.

Finishing the exterior.   If you're building a Class B motorhome (van conversion) you may not have to make any changes in the exterior, if the existing paint is acceptable.  Some inter-city buses are have aluminum exterior "skin" that looks good without painting.  You may have to remove existing bus line decals or paint and give the rest a really good buffing.  The areas under paint or decals may be shinier than the original exposed surfaces and it may be difficult or impossible to restore full shine to aged surfaces, forcing you to paint the rig to get a satisfactory cosmetic appearance.  You might be able to get creative and cover the areas where the old logos were with new graphics or murals.  School buses can be repainted and in some jurisdictions, MUST be changed from their original yellow/orange color, but even with a snazzy paint job, it will still look like a school bus!   The addition of chrome wheel simulators adds a nice touch to just about any RV.   If you have the budget for it, you might remove the old painted bumpers and grill and have them chromed to help tone down the school bus image.  Upgrading to heavy-duty off-road style bumpers will give your rig a powerful, brutish or military look and personality while adding useful off road protection, but can be quite expensive.

Wiring your home-made RV shouldn't be a big problem for anyone with familiarity with wiring techniques and requirements.  If you aren't comfortable with electrical wiring, enlist the aid of a qualified electrician.  I did all my own wiring on my enclosed motorcycle trailer.  I recommend being generous in your installation of both 120-volt and 12-volt outlets and lights.  It is a lot easier to run wiring during construction than after! Y ou will probably have two wiring systems: 12-volt and 120-volt.  The 12-volt system will power your interior lights and provide places to install 12-volt accessories.  You may also want to run speaker wires for radios and entertainment systems.  Minimum components would include one or more batteries, a converter, and a fuse panel.   I suggest you plan for using 2 6-volt batteries wired in series for your 12-volt system.  6-volt golf cart batteries are stronger, have more power, and last longer than 12-volt RV batteries.  Your converter should include a high power (at least 40 amp) multi-stage battery charger.   You may find cheaper converters without strong battery chargers.  In that case, you might simply add an automatic automotive battery charger.  When doing your own wiring you have the option to run switches to convenient locations. Something that is very handy but few RVs have, is a 3-way switch for the water pump, with one switch on the main control panel and a second switch in the bathroom.   If you have trouble finding 3-way switches you can wire DPDT switches to serve the purpose.  You have to wire them so that in one position the hot wire is connected to the fixture and in the other position the hot wire is connected to the other switch.  When I wired my enclosed motorcycle trailer, I used ordinary 120-volt residential light switches in convenient locations (like just inside the door) instead of puny little 12-volt toggle switches that often have a tendency to get broken off.  I even used standard 3-way 120-volt switches for my outside work lights so I could turn them on and off from a waterproof outside switch.  Your second wiring system is the 120-volt wiring.  You need a shore power cord, or at least a way to plug into shore power.   I copied something I'd seen on older truck campers for the power connection for my motorcycle trailer.  It is called a "motor base" and is essentially a male plug built into a receptacle so you can plug the female end of any heavy duty extension cord into it.  This works OK for low power requirements.   If you plan to have a roof A/C you will need at least a 30-amp circuit to power it, and that takes a stronger connection and a heavier power cord. Your 120-volt shore power should run directly to a set of circuit breakers that protect all the on board circuits.   Roof A/C should have its own circuit.  So should any other high power appliances. Your 12-volt converter should also have its own 120-volt breaker.  The converter converts 120-volt AC power to 12-volt DC power.   If you plan to have a microwave oven, install an outlet inside the cabinet where it will go and put it on its own circuit breaker.  You will want to run outlets to convenient locations throughout your RV. Check with an electrician to decide how many outlets you should put on each circuit.   I like to separate the circuits "geographically" so if something trips a breaker, it will be easy to know where the problem is.   If ALL the outlets are on one circuit, anything could be the culprit.  I would put the street side of each "room" on one circuit and the curb side on the other.  Plus a separate circuit for the kitchen and the bathroom.   That means in a typical RV with a living area and a bedroom, I'd have at least 6 outlet circuits, but that might not be possible on a 30 amp service since each circuit would be at least 15 amps.   Bathroom and kitchen outlets should be GFCI protected.  GFCI protection can be provided via special breakers or outlets.  Regardless of how many outlets or breakers you install, keep track of the total amperage of your appliance to be sure you don't exceed the input capacity for your RV (typically 30 amps, sometimes 50 amps on larger units with multiple air conditioners).  The input power cord should be connected to a main breaker that is rated properly for the power cord.  Take care running all your wiring and avoid anyplace it could be pinched or frayed.  Use grommets to protect wiring passing through metal or through any panels with sharp edges.  You might want to install a few 120-volt lights at various locations inside and outside your RV.   If you do the wiring yourself, I strongly suggest you familiarize yourself with residential wiring codes and make sure you meet all the minimum standards for wire gauge, circuit breakers, etc.   Make sure all connections are tight.  If you are going to have an on board generator, you will need to either install an automatic transfer switch to switch between shore power and generator power or install a receptacle tied to the generator into which you can plug your shore power cord when you want to use the generator. RVs are typically wired with either 30-amp or 50-amp service, with 30-amp being the most common and what you will find at more campgrounds.  Large luxury motorhomes and trailers may have 50-amp service.  What you need is determined by the total electrical load you expect to operate simultaneously.  If you have a 30-amp supply and enough high power appliances to exceed 30 amps, you will need to alternate use of some appliances.   Otherwise you'll blow circuit breakers to perhaps even overheat some wiring and cause a fire.  I've seen people use adapters to connect their 30 or 50 amp motorhomes to an ordinary 15-amp household outlet and run a standard duty extension cord to accommodate long distances -- and I've seen the extension cords melt before tripping a circuit breaker.  You may have to do some math to determine what your load is -- or can be at any one time. Most appliances are rated in watts.   Watts = volts * amps, so to get amps, divide the watts by 120. Thus, a 1200 watt, 120 volt appliance, like an iron or a hair dryer, will draw 10 amps.

Plumbing is a major part of your design and construction process.   Sinks and shower pans designed for residential use probably won't fit in comfortably in an RV so you'll need fixtures designed for RV use.  You need to understand the right slope for proper drainage.  If your RV is going to be used for winter camping, you will want to protect the plumbing from freezing by enclosing holding tanks and heating the compartment containing dump valves.  Drains can be built using ordinary black ABS pipe you would use in a residential application.   Fresh water lines are usually plastic or PEX and may require special crimping tools for making watertight connections.  Most RVs are designed so the toilet empties directly into the top of the black water tank.   If, for any reason, your toilet cannot be placed over the black water tank, you will need to buy a special power flushing toilet.  Grey water from sinks and showers need only have the right slope for proper drainage plus "P" traps and vacuum breakers to control odors.  Sewer lines must also be vented up through the roof. You will need to locate fresh water and waste water holding tanks in appropriate locations.  If you plan to use the RV in freezing weather, all water tanks, both fresh and waste, should be in an enclosed and heated space or equipped with heating pads.  Black water holding tanks normally need to be located directly below the toilet.  Put your dump valves as close to the tanks as you can where you can conveniently reach them and where they will drain the waste tanks completely.

Propane systems are needed for the stove, furnace, hot water heater, and most refrigerators.   The propane tank must be located outside the living space in a well ventilated area.   Motorhomes should have permanent propane tanks.  Trailers usually have removable tanks.  You will need to consider the location of your tank and the location of your appliances and plan proper routing of gas lines to supply fuel to each appliance.  Trailer tanks are usually mounted on the trailer tongue.   If you are building an RV that will ONLY be used in full-hook up campgrounds you might be able to get by with all electric appliances.   They could even be used for short periods with power from an on board generator, but you wouldn't want to count on using a generator to provide electricity for heating your RV at night.  Running your generator at night is prohibited in most campgrounds, is inconsiderate to fellow campers in primitive camp sites, and it can be dangerous.   Should an exhaust leak develop or you just get the wrong breeze, you could be killed by carbon monoxide as you sleep.  Carbon monoxide is tasteless and odorless and is known as "the silent killer".

That brings up the subject of warning systems.   You must install smoke detectors in your RV to meet RV codes and for the safety of you and your traveling companions.  Carbon monoxide detectors are highly recommended.   LP Gas detectors are also required on commercially built units and you should plan on including one if you are building your own RV.  While RV propane systems are usually pretty robust and reliable, normal road vibration can cause connections to loosen and leak and you definitely want to know long before the concentration reaches a critical level, which is something around 22,000 parts per million.  Detectors are usually set to go off at about 1/10 that concentration, providing a good margin of safety.  Be sure to buy RV rated detectors.  Residential models won't stand up to the vibration and stress of travel.

Hybrid conversions.  I don't know what else to call them.  I use this term to describe travel trailers mounted on truck chassis.   The very first "motorhome" I ever encountered was built and owned by a neighbor back in Idaho.   He had removed the bed of an old pickup truck and mounted a small Shasta travel trailer.  This kind of work takes some heavy lifting and carefully engineered mounting but avoids all the tedious work of building cabinets, doing plumbing and wiring, and installing appliances and furniture.  You have ready-made living quarters.  For this kind of work you'll need some heavy duty hoists or cranes to lift the trailer and position it on the truck chassis.  You will have to design and build appropriate mounts and braces to attach the trailer to the truck frame. 

Building your own RV can be a very satisfying and rewarding, if time consuming, experience. Chances are, no matter how well you plan, you will encounter unexpected obstacles, costs, and delays or things that won't fit quite the way you thought they would.  Keep that in mind and be prepared for it.  I recommend setting aside at least an extra 20% (time and money) for surprises that come up along the way.

With all this in mind, creating a basic camping vehicle need not be an overwhelming job.  You may want to start small and get some practice before undertaking a major conversion.   It will also give you time to assess you needs and wants. My first "camper" was an old Chevy suburban that was a retired maintenance vehicle from a local school district. I didn't do any real "conversion" per se.   I just added curtains on the windows for privacy and stocked it with my tent camping equipment (stove, ice chest, sleeping bags).  A 3-gallon plastic water jug and and plastic dishpan provide for basic hygiene and washing dishes.  Essentially, it was my "tent on wheels".  It certainly wasn't fancy, but it sure was nice to roll into camp, roll out our sleeping bags in the back, and be ready for a good night's sleep while our fellow campers were out wrestling with their tents in the dark and the wind. And it was really pleasant to listen to the staccato sounds of the rain on the metal roof instead of worrying about our tent leaking in a downpour or listening to it flap in the wind.  Just imagine how much more secure (though a bit noisy) it is in hail!   Our trusty Coleman lantern was usually all the heat we needed in the limited space on cool evenings.  Technically, it couldn't be described as a motorhome, but it did provide a lot of camping convenience at very low cost.  An old van or StepVan would work well too, especially if they have stand-up head room, which my Suburban didn't.  It isn't much fun trying to get your pants on when you can't stand up.  That's where an SUV tent might have been a good addition but since that was before Suburban's were classified as SUVs, it wasn't an option at the time.   Of course you could always set up a cabin tent adjacent to your vehicle to serve as a dressing room and extended living area.  Today you can do wonders with an SUV and available accessories.

Do it yourself!

Spare Parts for RVs, OHVs, Boats, and Camping

Over the years I've found it useful to maintain a supply of spare parts for my RVs, OHVs, and camping equipment.   The first dirt bike trip we took I didn't even have spare spark plugs for our dirt bikes -- a definite problem for 2-stroke engines that foul plugs quite easily.   I soon learned to carry not only spare spark plugs, but spare brake and clutch levers, master links to repair broken chains, spare inner tubes, and a variety of nuts and bolts to keep things together.   I also find it helpful to stock spare parts for camping equipment.  Stoves, lanterns, tents, sleeping bags, and backpacks all need repair sooner or later and it is REALLY nice to have the right parts and patches already on hand. Being able to repair things on the spot can prevent damage from getting worse as well as saving your outing.

Some basic RV or other vehicle parts I recommend everyone should carry include fan belts and radiator and heater hoses.  I also carry a thermocouple or two in case I need to fix a furnace, water heater, or refrigerator.  They are only used on older units.  Newer appliances with computer controls use a thermal sensor instead of a thermocouple.  Extra hose washers are good to have, especially if you have access to city water hookups.   Extra nuts, bolts, and screws of various sizes also come in handy. A universal faucet repair kit or a "storehouse" of faucet washers can also be useful if something starts to leak out in the boondocks.  An extra dump valve is essential if yours is prone to get knocked off. Some hang down way too low and are all too frequently damaged.   I like to carry a couple of compression elbows and compression sleeves in case something happens to the fresh water tubing.  Spare light bulbs for all the different light fixtures will definitely come in handy.  Most RV incandescent lights use a standard, single contact, automotive 1146 bulb.   I like to carry some spare, dual contact 1157s for tail/stop and park/turn signal lights too.  Some extra dash lights will let you see your instruments and some clearance marker bulbs may be needed from time to time.   Might save you an unscheduled stop by a highway patrolman and perhaps even avoid a fix-it ticket.  Check your owners manual or pull some sample bulbs to be sure of the part numbers you need for each application.  You might find LED equivalents that would reduce power usage.

Spare OHV parts will be determined by the type of OHVs you have and what kind of things typically go wrong -- and by the kinds of repairs you are comfortable with or capable of doing.  I've found that spare spark plugs, spare levers, and spare inner tubes are basic items and have saved many a weekend outing.   Spare fasteners are essential since things tend to come loose frequently out on the trails.   When I first started riding I had to get a handful of spare nuts and bolts from the mechanic at my motorcycle dealer.  Today you can buy nice little compartmentalized boxes of fasteners specifically selected for the needs of most dirt bikes and ATVs by brand at your local motorcycle/ATV shop.  The $20-$50 you invest will pay itself back in only a few outings and is sure to me far less than you'd pay if  you had to take your machine in for repairs.  Having the right parts makes repairs easier.  Not only will they look and fit better, you avoid possible further damage by trying to make do with fasteners with the wrong threads or ones that are too long or otherwise incorrect.  If you can't find a ready-made kit for your ride, get a "storehouse" of metric fasteners from your local hardware store or Harbor Freight or just buy a handful of the size you use most frequently at your local hardware store.  They may not be as cosmetically correct as factory parts or the ones from branded kits, but at least they'll hold things together until you can get home and get the right parts. 

Likewise, the spare parts you need on a boat will depend on the type of boat.  The things you need on a sailboat will be different than what you need on a power boat.  Basic spare parts for a sailboat include shackles, sail tape, and rope repair items.  Parts for a power boat will depend on the type of motor and other features on board.  Hose clamps are usually a good idea to have around if you have any plumbing on board.

What kind of spare parts do you need for your camping equipment?   Extra tent pegs are always good to have on hand.  Extra tent poles could also be helpful.  A grommet kit for repairing or adding grommets to tents or tarps is always useful.  A tent repair kit is essential.  They usually include nylon patches for fixing tears in the tent fabric and some netting to fix holes in screens.   These patches can usually be used to repair sleeping bags and nylon jackets as well.  Some of the patches are self adhesive and very easy to use.   For sturdier and more permanent repairs bring along a heavy duty sewing kit, which should include an awl as well as large needles and strong thread.   Some tent repair kits include parts to repair fiberglass shock-corded tent poles or you can buy tent pole repair kits.  Spare parts for your Coleman lanterns and stoves are essential.  Lantern mantles are quite fragile and it is not unusual to go through several pairs in a single weekend outing.  Repair kits for the pumps for gas lanterns and stoves are fairly small and inexpensive and can save an outing.  Generators for lanterns and stoves run about $12-$15 but are worth much more than that if you need one unexpectedly.   If you have any backpacks, spare anchor pins that hold the canvas to the frame and buckles for the belts and straps are items that are frequently lost or broken on the trail.  Extra rope for tying down your tent or securing tarps should be on your list.  I also like to have a handful of "cord locks", those little spring thingies that hold sleeping bag cords tight when the bag is rolled up.   You can often buy them in bulk at bargain prices on ebay.  I paid $1.50 for 2 at a local sporting goods store when I needed some right away.  Later I found a package of 50 for $3.45 and free shipping on ebay so I'm stocking up for future needs . A ball of binder's twine will always find many uses around camp.   Stocking spare batteries and bulbs for your flashlights should go without saying.

Purchasing ALL the spare parts you may need at one time could be quite expensive so you may want to make a list and do a few things at a time.  That also allows you to keep an eye out for bargain prices on the things you need to stock up on.  You should prioritize your list so you can get the most important things first, but buying least expensive things first or taking advantage of special sales are also good strategies.  If you see something that isn't on your list but you think will be useful, grab it while you can!  Otherwise you'll soon be kicking yourself out on the trail when you need it.   I don't think I have EVER looked at a tool or spare part in my trailer, RV, or fanny pack and said "Gee, I wish I hadn't bought that" but there have been MANY times I've been in the position to say "Gee, I wish I had gotten that when I had the chance!"   I have found ebay to be a good source for many tools and spare parts for RVs, OHVs, and camping equipment.

Anyway you cut it, having spare parts on hand will save time and often save money as well as avoid untimely interruptions of your activities.  Feel free to expand on the items suggested in this article to include anything that you think will make your outings less stressful and more successful.  If you find you repeatedly need certain things during your trips or have to make trips to town or the camp store for things, add them to your supplies.  In the long run it will save you money as well as time and frustration.

Stock up!

RV Parts and Accessories

There are way too many RV parts and accessories to list in a single article.  The list would be endless and would undoubtedly be out of date by the time I could click the "publish" button, let alone by the time you read it.  However, there are some traditional parts and accessories that are worth mentioning and watching for bargains on.  

So what is the difference between "parts" and "accessories"? You can think of "parts" as essential components of your RV and "accessories" as optional features or gadgets that add convenience or fun.  Even if you don't have an immediate need for some of these things, you might want to snag them while they're available if you come across them at a good price.  For years I've "stockpiled" some frequently needed RV parts and accessories so I have them on hand when I need them.  Things that could be used as replacement parts on your current RV should be high on your list.   For example, I grabbed a complete Chevrolet P-30 instrument cluster on ebay.com . Turns out I then moved on to a Gillig-based Holiday Rambler so I didn't think I'd probably never use it, but when I owned several P-30 based motorhomes, I had a spare in case of failure.  Now I have another P-30 based motorhome so it may yet come in handy.  I got it on ebay at a very reasonable price so it didn't involve tying up a ton of money.   Gathering parts for older motorhomes before they become scarce is something to think about.  You also may want to consider investing in interesting accessories you might want to add or to have on hand for a subsequent RV if the price is right and you can both afford it and have a place to safely store it until you can use it.   No point storing a set of RV dinette cushions if they're going to be susceptible to deterioration due to weather, sunlight, insects, vermin, or humidity.  On the other hand, disposable items or things that tend to need to be replaced often are always good to stock up on.  I still have a spare motor for the electric steps on my motorhome.

Roof vents and covers.  Because of nearly constant exposure to sunlight, plastic roof vents and covers tend to deteriorate over time and have to be replaced every few years.  Covers for many 14x14 vents are interchangeable and ANY 14x14 vent can be fairly easily removed and replaced by another brand.  When buying replacement covers, make sure they will fit your existing vents.  Different brands have slightly different designs that make them incompatible with each other.   Since changing the cover itself is much easier and cheaper than changing a whole vent, having a few extra matching covers on hand has saved me a lot of time, frustration, and money over the years.  In some cases I bought whole new vents and have always found a good use for them.  Some roof vents include 12 volt fans. The least expensive versions have small vans mounted within normal 14x14 vents.  More powerful models, like the Fantastic vents, have large 10 or 12", multi-blade fans than move LOTS of air.  Most vents are or can be wired to be reversible so they can be used to exhaust hot inside air or draw in outside air.  Simply reversing the polarity of the 12-volt dc connections will usually do the trick and you can do this by cross-wiring the fan to a DPDT (Double Pole Double Throw) switch so you can swap hot and ground wires going to the fan.  The more expensive powered vent models usually have multiple fan speeds and may even have rain sensors and thermostats to automatically control the fan and close the vent when needed.  You may need to consider the thickness of your roof in order to get vents and interior trim that will fit.  Most vents allow quite a bite of flexibility, but if you have a particularly thick roof (like some vehicles with ducted A/C in the ceiling) standard vents might not be deep enough to fit.

Another thing I've found useful to stockpile are lenses for various RV light fixtures.  This includes tail lights, clearance lights, porch lights, and interior lights.  These light weight plastic lenses are easily damaged and it is handy to have a supply of replacements on hand -- especially if you can get them at bargain prices.   I look for closeouts at RV and auto parts stores as well as good deals on ebay and other online sites.   For older units look for items described as "NOS" (New Old Stock).  I also keep several complete light fixtures on hand in case one fails -- or I want to add one to a new rig.

Salvage yard bargains.  Some things you might want to pick up from a "retired" RV at a salvage yard (if the price is right) might include windows, converters and water pumps.   I've had to replace enough of them over the years to know that having them already in inventory can save me a lot of time and money.  They have also provided a resource to build up the capabilities of my enclosed motorcycle trailer.   I have also been able to get really good deals on a furnace from an old camper and a roof air conditioner from a motorhome, both of which found their way into my motorcycle trailers over time.

12 volt fans have several useful functions in an RV.  Mounted at the windshield, they can help reduce fogging in damp, cold weather.   On warmer days they can provide a cooling breeze to the driver and co-pilot.   Installed near the seating, dining, or sleeping areas, they can help make those areas more comfortable.   Portable models, equipped with spring clamps, can be plugged into 12-volt sockets (like cigarette lighter sockets) and moved about as needed.  You can sometimes find these fans on sale in auto stores and department stores like K-mart and Walmart.   I like to have a couple of backup fans on hand and keep my eyes open for good deals.  If you shop for them online, be sure to include the shipping cost when you compare the price to local stores.  Sometimes shipping and handling will push the price way above what you can get it for locally.  And never assume an auction price will be lower than retail.  I frequently see people bidding way high on items that are readily available in local stores.   For example, I recently saw a bid of $32 for a standard trailer/BBQ sized propane tank, and shipping of such a heavy and bulky item will push the cost even higher. Similar tanks are routinely available at Home Depot for around $29.97 -- and you get it right away and you don't have to pay shipping when you pick it up at the store.  Make sure any bulk propane tank you buy meets current standards.  That means a portable tank must have an OPD (Overfill Protection Device).  It is not legal to refill the older tanks anymore.  If you have one that still has some fuel in it you can probably use it up on your camper or BBQ but you won't be able to refill it.  I've seen kits that can be used to convert retired propane tanks to compressed air tanks so that might be a useful option.

Awnings are always nice to have, both large patio awnings and smaller window awnings.  As they can be quite expensive, it is good to watch for bargains on them.  Both ebay and craigslist are good sources for possible candidates.   I haven't found it economically practical to "stockpile" awnings, but I have been able to equip several vehicles with window awnings at a fraction of the regular retail price as needed using ebay.   I have usually had to settle for plain white awnings instead of color coordinating them with the RV paint scheme like you would if you bought them at an RV store, but, at least to me, the savings was well worth it.   I've also gotten a couple of used patio awnings for my enclosed motorcycle trailers at bargain prices. If the awning color doesn't meet your needs, you can usually paint them any color you choose using vinyl paint.  I changed one from magenta to blue and again to brown that way to match changing color schemes on my enclosed motorcycle trailer.

Lighting options are as varied as your imagination.  There are many choices for both interior and exterior lights. LED lights have the advantage of saving battery power, but the bulbs are quite expensive.  Typical 12-volt incandescent automotive type bulbs used in traditional RV fixtures are typically under $1.00 each.  You'll pay about 5-10 times that for LED replacements.   Of course they will last much longer than regular bulbs and will conserve battery power -- definitely an advantage when boondocking.  LEDs last a very long time and over their lifetime will be cheaper than continuously replacing damaged or burned out incandescent bulbs.  To ensure you gain the financial benefits, consider how long YOU will be able to use the LEDs, not just how long they are rated to last.   If you trade RVs every 3 years or so or don't expect to keep your RV, you'll never see the savings.   Immediate benefits of upgrading to LED lights are clear, bright illumination and reduced battery drain.

Kitchen accessories.  The list of gadgets promoted for use in RV galleys is endless and growing every day.  And you certainly aren't limited to what you find in camping and RV stores.  You can find useful items many other places, like your favorite grocery store, department stores, even dollar stores. We found a clever little single beater mixer at Dollar Tree.   It works like a push drill.   Each push of the handle rotates the beater about 10 times.  It is made of plastic and isn't designed for heavy use so you wouldn't want to try mixing bread dough with it, but it is small and light so it is easy to transport and store and works very well for mixing smoothies and other single-serving beverages and other light mixing tasks like scrambling eggs.   And it requires no power, except a little muscle power.  Anything that conserves power when boondocking is an advantage. High end RVs often have built in power centers for mixers, food processors, and a variety of attachments.  Nutone is one popular built in brand whose attachments include blenders, mixers, can openers, knife sharpeners, and ice crushers.  If your RV isn't equipped with one, you can sometimes find them on ebay.  You'll probably have to run 120 volt power under the counter for it unless there is already an outlet inside the cabinet.  The benefits of such systems include convenience and not having to carry separate appliances, but the attachments can take up quite a lot of room.  Expect to pay $600 - $700 for a complete Nutone system.

RV ladders often do more than provide access to the roof.  Watch for attachments to carry camp chairs and bicycles.  These handy racks attach to your RV ladder, providing a convenient location to carry bulky, light weight items like camp chairs and bicycles.  When using them make sure the items don't cover your tail lights.   I added some PVC sleeves to my ladder to hold the pole for a 500-watt halogen floodlight for when we need a lot of campground illumination.

Storage options, like roof pods or racks that mount in your trailer hitch are worth watching for. There are also hitch-mounted "trunks" that provide enclosed external storage.  Since these items tend to be kind of pricey, you'll want to watch for sales, closeouts, and good deals on used items.

Dress up items, like wheel liners, are a nice addition to any RV that has ordinary steel wheels and wheel covers.   Not only do they provide a modern, upgraded appearance, the bolt-on versions eliminate the rattle that sometimes is found with wheel covers.   Other dress up items include upgraded rear view mirrors, roof or windshield post mounted search lights, and air horns.  I always added bumper guards to the van bumpers on my Class B RVs.   Driving and fog lights can improve visibility and safety as well as dress things up a bit.  I have a set of combination driving lights on my current Class A motorhome.   Each light has a split lens, half yellow (for fog lights) and half clear (for driving lights).   Fog and driving lights can be purchased at any auto parts store or the automotive department of any department store.  Be sure you wire them in accordance with state laws.  Some states only allow driving lights to be used in conjunction with low-beams.  Others require driving lights to be dimmed like high beams when approaching another vehicle.  In any case, take care to align fog and driving lights to give you maximum lighting of the road WITHOUT shining in the eyes of approaching drivers.  This usually means aiming them somewhat low and to the right.

Compasses, altimeters, and clinometers are also useful additions to most motorhomes and tow vehicles.  You may also find them helpful when car camping.   My favorite compass is a monster called a RoadMaster, but I don't think it is still available new.   You might find an older one on ebay.   It can be wired into your dash lights for nighttime viewing.   Altimeters tell you altitude.  A clinometer indicates the attitude of the vehicle -- front to back and side to side.  This can be helpful in finding the most level spot in your campsite.  They are also sometimes used in off-road vehicles to measure extreme positions and (hopefully) avoid roll overs.  Standard glass-vial bubble levels are inexpensive, easy to install, and let you get a pretty precise leveling of your unit -- IF you install them correctly with the vehicle level in the first place.  The ones designed for cockpit use are each about 3" long but you can get huge versions to mount on the front of a trailer so you can see it in your rear view mirror.   Always make sure the vehicle is level before you install bubble levels.

GPS and navigation devices are still a bit pricey, but provide wonderful functionality in helping you through unfamiliar territory.   I've had built in navigation systems in my daily driver but would never do that again.  A portable or hand held unit, is much more flexible as you can use it in multiple vehicles.  Most current models provide visual and voice turn-by-turn directions as well as lat/long coordinates.  Some even accept voice commands so they can be used hands free.

If you need RV parts, I've found the folks at Winnebago Outdoor to be especially helpful.   Many RV manufacturers use the same parts so you may find what you need even if your RV isn't a Winnebago brand.

Accessorize!